123 lines
7.3 KiB
C
123 lines
7.3 KiB
C
|
||
#ifndef __CH395CMD_H__
|
||
#define __CH395CMD_H__
|
||
#include "ch395inc.h"
|
||
//#include "./SYSTEM/sys/sys.h"
|
||
|
||
|
||
void ch395_cmd_reset(void); /* 复位 */
|
||
|
||
void ch395_cmd_sleep(void); /* 睡眠 */
|
||
|
||
uint8_t ch395_cmd_get_ver(void); /* 获取芯片及固件版本号 */
|
||
|
||
uint8_t ch395_cmd_check_exist(uint8_t testdata); /* 测试命令 */
|
||
|
||
void ch395_cmd_set_phy(uint8_t phystat); /* 设置phy状态 */
|
||
|
||
uint8_t ch395_cmd_get_phy_status(void); /* 获取phy状态 */
|
||
|
||
uint8_t ch395_cmd_get_glob_int_status(void); /* 获取ch395全局中断状态 */
|
||
|
||
uint8_t ch395_cmd_init(void); /* 初始化ch395 */
|
||
|
||
void ch395_cmd_set_uart_baud_rate(uint32_t baudrate); /* 设置波特率 */
|
||
|
||
uint8_t ch395_get_cmd_status(void); /* 获取命令执行状态 */
|
||
|
||
void ch395_cmd_set_ipaddr(uint8_t *ipaddr); /* 设置ch395的ip地址 */
|
||
|
||
void ch395_cmd_set_gw_ipaddr(uint8_t *gwipaddr); /* 设置ch395的网关ip地址 */
|
||
|
||
void ch395_cmd_set_maskaddr(uint8_t *maskaddr); /* 设置子网掩码 */
|
||
|
||
void ch395_cmd_set_macaddr(uint8_t *amcaddr); /* 设置ch395的mac地址 */
|
||
|
||
void ch395_cmd_get_macaddr(uint8_t *amcaddr); /* 获取mac地址 */
|
||
|
||
void ch395_cmd_set_macfilt(uint8_t filtype, uint32_t table0, uint32_t table1); /* 设置ch395的mac过滤 */
|
||
|
||
void ch395_cmd_get_unreachippt(uint8_t *list); /* 获取不可达地址以及端口 */
|
||
|
||
void ch395_cmd_get_remoteipp(uint8_t sockindex, uint8_t *list); /* 获取远端ip和端口，一般在tcp server下使用 */
|
||
|
||
void ch395_set_socket_desip(uint8_t sockindex, uint8_t *ipaddr); /* 设置scoket n的目的ip地址 */
|
||
|
||
void ch395_set_socket_prot_type(uint8_t sockindex, uint8_t prottype); /* 设置socket n的协议类型 */
|
||
|
||
void ch395_set_socket_desport(uint8_t sockindex, uint16_t desprot); /* 设置socket n的目的端口 */
|
||
|
||
void ch395_set_socket_sourport(uint8_t sockindex, uint16_t surprot); /* 设置socket n的源端口 */
|
||
|
||
void ch395_set_socket_ipraw_proto(uint8_t sockindex, uint8_t prototype); /* 在ipraw模式下，设置socket n的ip包协议字段 */
|
||
|
||
void ch395_set_recv_threslen(uint8_t sockindex, uint16_t len); /* 设置socket n的接收中断阀值 */
|
||
|
||
void ch395_send_data(uint8_t sockindex, uint8_t *databuf, uint16_t len); /* 向socket n的发送缓冲区写数据 */
|
||
|
||
uint16_t ch395_get_recv_length(uint8_t sockindex); /* 获取socket n的接收长度 */
|
||
|
||
void ch395_clear_recv_buf(uint8_t sockindex); /* 清除socket n的接收缓冲区 */
|
||
|
||
void ch395_get_recv_data(uint8_t sockindex, uint16_t len, uint8_t *pbuf); /* 获取接收数据 */
|
||
|
||
void ch395_cmd_set_retry_count(uint8_t count); /* 设置最大重试次数 */
|
||
|
||
void ch395_cmd_set_retry_period(uint16_t period); /* 设置最大重试周期 单位 毫秒 */
|
||
|
||
void ch395_cmd_get_socket_status(uint8_t sockindex, uint8_t *status) ; /* 获取socket n的状态 */
|
||
|
||
uint8_t ch395_open_socket(uint8_t sockindex); /* 打开socket n*/
|
||
|
||
uint8_t ch395_close_socket(uint8_t sockindex); /* 关闭socket n*/
|
||
|
||
uint8_t ch395_tcp_connect(uint8_t sockindex); /* tcp连接 */
|
||
|
||
uint8_t ch395_tcp_listen(uint8_t sockindex); /* tcp监听 */
|
||
|
||
uint8_t ch395_tcp_disconnect(uint8_t sockindex); /* tcp断开连接 */
|
||
|
||
uint8_t ch395_get_socket_int(uint8_t sockindex); /* 获取socket n的中断状态 */
|
||
|
||
uint8_t ch395_crcret_6bit(uint8_t *mac_addr); /* 多播地址crc32，用于hash过滤 function count = 36 */
|
||
|
||
void ch395_get_ipinf(uint8_t *addr); /* 获取ip，子网掩码和网关地址 */
|
||
|
||
uint8_t ch395_get_dhcp_status(void); /* 获取dhcp状态 */
|
||
|
||
uint8_t ch395_dhcp_enable(uint8_t flag); /* 启动/停止dhcp */
|
||
|
||
void ch395_write_gpio_addr(uint8_t regadd, uint8_t regval); /* 写gpio寄存器 */
|
||
|
||
uint8_t ch395_read_gpio_addr(uint8_t regadd); /* 读gpio寄存器 */
|
||
|
||
uint8_t ch395_eeprom_erase(void); /* 擦除eeprom */
|
||
|
||
uint8_t ch395_eeprom_write(uint16_t eepaddr, uint8_t *buf, uint8_t len); /* 写eeprom */
|
||
|
||
void ch395_eeprom_read(uint16_t eepaddr, uint8_t *buf, uint8_t len); /* 读eeprom */
|
||
|
||
void ch395_set_tcpmss(uint16_t tcpmss); /* 设置tcp mss值 */
|
||
|
||
void ch395_set_socket_recv_buf(uint8_t sockindex, uint8_t startblk, uint8_t blknum); /* 设置socket接收缓冲区 */
|
||
|
||
void ch395_set_socket_send_buf(uint8_t sockindex, uint8_t startblk, uint8_t blknum); /* 设置socket发送缓冲区 */
|
||
|
||
void ch395_udp_send_data(uint8_t *buf, uint32_t len, uint8_t *ip, uint16_t port, uint8_t sockindex); /* udp向指定的ip和端口发送数据 */
|
||
|
||
void ch395_set_start_para(uint32_t mdata); /* 设置ch395启动参数 */
|
||
|
||
uint16_t ch395_cmd_get_glob_int_status_all(void); /* 获取全局中断状态，收到此命令ch395自动取消中断,0x44及以上版本使用 */
|
||
|
||
void ch395_keeplive_idle(uint32_t idle); /* 设置keeplive空闲 */
|
||
|
||
void ch395_keeplive_intvl(uint32_t intvl); /* 设置keeplive间隔时间 */
|
||
|
||
void ch395_keeplive_cnt(uint8_t cnt); /* 设置keepalive重试次数 */
|
||
|
||
void ch395_set_keeplive(uint8_t sockindex, uint8_t cmd); /* 设置ttl */
|
||
|
||
void ch395_setttl_num(uint8_t sockindex, uint8_t ttlnum); /* 设置ttl */
|
||
|
||
#endif
|