120 lines
3.4 KiB
C
120 lines
3.4 KiB
C
#ifndef _PROVALCTRL_H_
|
|
#define _PROVALCTRL_H_
|
|
|
|
#include "modbus.h"
|
|
#include "dac7311.h"
|
|
#include "main.h"
|
|
//#include "flash.h" //擦写出错，写入出错
|
|
#include "eeprom.h"
|
|
#include "math.h"
|
|
|
|
#define CSTEP_WAIT_MAX 0 //逐步接近，等待时间
|
|
#define BIAS_MAX 10 //偏大大于此值时不进行控制
|
|
#define GAS_IN 0 //充气
|
|
#define GAS_OUT 1 //排气
|
|
#define SLDW_PRES_OUT 10 //输出气压的滑动窗口长度
|
|
|
|
extern float ao_dwq; //AO输出电流值(定位器)
|
|
extern float ao_blf1; //AO输出电流值(比例阀)
|
|
extern float ao_blf2; //AO输出电流值(比例阀)
|
|
|
|
typedef enum
|
|
{
|
|
PROV_RUNNING = 0, //运行
|
|
PROV_ADJUSTING = 1, //整定
|
|
PROV_HOLDING = 2 //保持原样，不进行校准
|
|
}prov_status;
|
|
|
|
typedef enum
|
|
{
|
|
ADJ_START = 0, //整定开始
|
|
ADJ_MOVE2MIDDLE = 1, //输出气源气压的一半，移动至中间位置附近
|
|
ADJ_OSCILLATE = 2, //继电反馈，强制振荡
|
|
ADJ_CALCULATE = 3, //计算结果
|
|
ADJ_END = 4, //整定结束，等待一段时间后恢复控制
|
|
ADJ_WAIT = 5 //等待，未进入整定程序
|
|
}adj_steps;
|
|
|
|
typedef struct
|
|
{
|
|
prov_status status; //比例阀状态
|
|
unsigned char tag; //标签，用于区分
|
|
|
|
float previous_pressure[SLDW_PRES_OUT]; //前几个时刻的输出气压
|
|
float current_pressure; //当前输出气压
|
|
float current_percent; //当前输出气压百分比
|
|
float target_pressure; //目标气压
|
|
float target_percent; //目标气压百分比
|
|
float target_current; //目标值的理论电流
|
|
float current_input; //当前电流输入
|
|
float input_max; //输入电流上限
|
|
float input_min; //输入电流下限
|
|
float bias; //偏差百分比
|
|
float bias_previous; //前一个偏差
|
|
float bias_area; //允许的误差范围 [-a, a]%
|
|
uint8_t gas_direction; //
|
|
|
|
float Kp; //比例系数
|
|
float Ti; //积分时间
|
|
float Ing; //积分项
|
|
float Ing_sum; //积分求和
|
|
float Ing_max; //求和上限
|
|
float Ing_min; //求和下限
|
|
float Td; //微分时间
|
|
float Ts; //采样时间（控制周期）
|
|
float Div; //微分项
|
|
float pidout; //PID输出
|
|
float pidout_max; //PID输出上限
|
|
float pidout_min; //PID输出下限
|
|
uint8_t slow_down_flg; //减速标志
|
|
|
|
// float cstep_gasin; //逐步接近，充气步长
|
|
// float cstep_gasout; //逐步接近，排气步长
|
|
// float cstep_max; //步长上限
|
|
// float cstep_min;
|
|
// unsigned char cstep_wait; //步长下限
|
|
|
|
void (*pvout)(float pout); //dac 输出
|
|
}propotion_valve; //比例阀参数结构体
|
|
|
|
|
|
#define OSCILL_TIMES 5 //振荡次数
|
|
#define TICK_LIMIT 120 //振荡周期限时
|
|
typedef struct
|
|
{
|
|
unsigned char adj_flag; //整定标志，用于判断是否处于整定中
|
|
float relay_d; //继电反馈，回环幅值
|
|
float relay_a[OSCILL_TIMES]; //继电反馈，输出气压振荡幅值，中间数据
|
|
float relay_A; //继电反馈，输出气压振荡幅值，结果
|
|
float relay_tc[OSCILL_TIMES]; //继电反馈，输出气压振荡周期，中间数据
|
|
float relay_Tc; //继电反馈，输出气压振荡周期，结果
|
|
float air_source; //气源压力
|
|
float middle_current; //中间位置电流
|
|
unsigned char oscil_times; //当前振荡次数
|
|
|
|
}prov_adjust; //自整定参数结构体
|
|
|
|
extern propotion_valve pv_one;
|
|
extern propotion_valve pv_two;
|
|
|
|
void prov_init(void);
|
|
void prov_adj_init(void);
|
|
void prov_set(float target_p, propotion_valve *pvx);
|
|
void prov_ctrl(propotion_valve *pvx, prov_adjust *adj_pvx);
|
|
void prov_calibrate_pid(propotion_valve *pvx);
|
|
void prov_calibrate_step(propotion_valve *pvx);
|
|
void analog_ctrl(void);
|
|
float abs_bias(float bias);
|
|
void prov_adj(propotion_valve *pvx, prov_adjust *adj_pvx);
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/******************************************************************************************/
|
|
#endif
|
|
|
|
|