224 lines
9.7 KiB
C
224 lines
9.7 KiB
C
#include "tmc5160.h"
|
||
#include "main.h"
|
||
#include "gpio.h"
|
||
#include "spi.h"
|
||
#include "delay.h"
|
||
#include "string.h"
|
||
|
||
// CS2置于 “低电平” 使能SPI
|
||
// 写的时候高位地址要加上 0x80
|
||
// 手册第5章是寄存器表，5.3.1是斜坡相关寄存器；第11章有实际单位换算表；第20章 图20.3 有运动控制流程图
|
||
// 寄存器 "RAMPMODE"->"0x20" 斜坡运动模式： 0->位置模式；1->速度模式至正VMAMX；2->速度模式至负VMAX；3->速度保持不变，最多使用2位
|
||
// 寄存器 "VSTART"->"0x23" 电机起动速度，最多使用18位，VSTART<=VSTOP
|
||
// 寄存器 "A1"->"0x24" VSTART->V1的加速度，最多使用16位
|
||
// 寄存器 "V1"->"0x25" 第一加/减速阶段速度阈值，最多使用20位；取0时禁用A1和D1，仅用AMAX和DMAX
|
||
// 寄存器 "AMAX"->"0x26" V1->VMAX的加速度，最多使用16位
|
||
// 寄存器 "DMAX"->"0x28" VMAX->V1的减速度，最多使用16位
|
||
// 寄存器 "VMAX"->"0x27" 斜坡运动目标速度，最多使用23位
|
||
// 寄存器 "D1"->"0x2A" V1->VSTOP的减速度，最多使用16位，不要在位置模式下置0
|
||
// 寄存器 "VSTOP"->"0x2B" 电机停止速度，最多使用18位，VSTART<=VSTOP，位置模式下>=10
|
||
// 一圈 200*256 微步，即每步转动 9/1280 度， 1 微步/秒 = 1.953e-5 转/秒
|
||
|
||
#define TMC5160A_CS2_L HAL_GPIO_WritePin(GPIOC,CS2_Pin,GPIO_PIN_RESET) //CS2低电平
|
||
#define TMC5160A_CS2_H HAL_GPIO_WritePin(GPIOC,CS2_Pin,GPIO_PIN_SET) //CS2高电平
|
||
|
||
#define TMC5160A_MOSI_L HAL_GPIO_WritePin(GPIOB,GPIO_PIN_15,GPIO_PIN_RESET) //MOSI低电平
|
||
#define TMC5160A_MOSI_H HAL_GPIO_WritePin(GPIOB,GPIO_PIN_15,GPIO_PIN_SET) //MOSI高电平
|
||
|
||
#define TMC5160A_CLK_L HAL_GPIO_WritePin(GPIOB,GPIO_PIN_13,GPIO_PIN_RESET) //CLK低电平
|
||
#define TMC5160A_CLK_H HAL_GPIO_WritePin(GPIOB,GPIO_PIN_13,GPIO_PIN_SET) //CLK高电平
|
||
|
||
#define TMC5160A_ReadVal HAL_GPIO_ReadPin(GPIOB,GPIO_PIN_14) //MISO
|
||
|
||
void TMC5160A_Init_Gpio(void)
|
||
{
|
||
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
||
__HAL_RCC_GPIOB_CLK_ENABLE();
|
||
/**SPI2 GPIO Configuration
|
||
PB13 ------> SPI2_SCK
|
||
PB14 ------> SPI2_MISO
|
||
PB15 ------> SPI2_MOSI
|
||
*/
|
||
GPIO_InitStruct.Pin = GPIO_PIN_13|GPIO_PIN_15;
|
||
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
||
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
||
|
||
GPIO_InitStruct.Pin = GPIO_PIN_14;
|
||
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
||
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
||
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
||
}
|
||
|
||
|
||
|
||
void tmc5160_init(void)
|
||
{
|
||
// 纯SPI模式
|
||
// TMC5160_SPIWriteInt(0x00, 0x0000000C,1); // writing value 0x0000000C = 12 = 0.0 to address 0 = 0x00(GCONF) 0x00000008 不能移动 会左右抖动
|
||
// TMC5160_SPIWriteInt(0x03, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 1 = 0x03(SLAVECONF)
|
||
// TMC5160_SPIWriteInt(0x05, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 2 = 0x05(X_COMPARE)
|
||
// TMC5160_SPIWriteInt(0x06, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 3 = 0x06(OTP_PROG)
|
||
// TMC5160_SPIWriteInt(0x08, 0x0000000E,1); // writing value 0x00000011 = 17 = 0.0 to address 4 = 0x08(FACTORY_CONF)
|
||
// TMC5160_SPIWriteInt(0x09, 0x00010606,1); // writing value 0x00010606 = 67078 = 0.0 to address 5 = 0x09(SHORT_CONF)
|
||
// TMC5160_SPIWriteInt(0x0A, 0x00080400,1); // writing value 0x00080400 = 525312 = 0.0 to address 6 = 0x0A(DRV_CONF)
|
||
// TMC5160_SPIWriteInt(0x0B, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 7 = 0x0B(GLOBAL_SCALER)
|
||
// // 速度相关的驱动控制寄存器
|
||
// TMC5160_SPIWriteInt(0x10, 0x00061F0A,1); // writing value 0x00070707 = 460551 = 0.0 to address 8 = 0x10(IHOLD_IRUN)
|
||
// TMC5160_SPIWriteInt(0x11, 0x0000000A,1); // writing value 0x0000000A = 10 = 0.0 to address 9 = 0x11(TPOWERDOWN)
|
||
// TMC5160_SPIWriteInt(0x13, 0x00000010,1); // writing value 0x00000041 = 65 = 0.0 to address 10 = 0x13(TPWMTHRS)
|
||
// TMC5160_SPIWriteInt(0x14, 0x00000010,1); // writing value 0x00004189 = 16777 = 0.0 to address 11 = 0x14(TCOOLTHRS)
|
||
// TMC5160_SPIWriteInt(0x15, 0x00000010,1); // writing value 0x00000000 = 0 = 0.0 to address 12 = 0x15(THIGH)
|
||
// 斜波发生器运动寄存器
|
||
TMC5160_SPIWriteInt(0x20, 0x00000001,1); // writing value 0x00000000 = 0 = 0.0 to address 13 = 0x20(RAMPMODE)
|
||
// TMC5160_SPIWriteInt(0x21, 0x00000000,1); // writing value 0xFFCC12F0 = 0 = 0.0 to address 14 = 0x21(XACTUAL)
|
||
// TMC5160_SPIWriteInt(0x23, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 15 = 0x23(VSTART)
|
||
TMC5160_SPIWriteInt(0x24, 0x000003E8,1); // writing value 0x00001F07 = 7943 = 0.0 to address 16 = 0x24(A1)
|
||
TMC5160_SPIWriteInt(0x25, 0x0000C350,1); // writing value 0x0000C350 = 50000 = 0.0 to address 17 = 0x25(V1)
|
||
TMC5160_SPIWriteInt(0x26, 0x000001F4,1); // writing value 0x00004DF1 = 19953 = 0.0 to address 18 = 0x26(AMAX)
|
||
TMC5160_SPIWriteInt(0x27, 0x00000D40,1); // writing value 0x0006D3A0 = 447392 = 0.0 to address 19 = 0x27(VMAX)
|
||
TMC5160_SPIWriteInt(0x28, 0x000002BC,1); // writing value 0x00009B83 = 39811 = 0.0 to address 20 = 0x28(DMAX)
|
||
TMC5160_SPIWriteInt(0x2A, 0x00000578,1); // writing value 0x00007B87 = 31623 = 0.0 to address 21 = 0x2A(D1)
|
||
TMC5160_SPIWriteInt(0x2B, 0x0000000A,1); // writing value 0x0000000A = 10 = 0.0 to address 22 = 0x2B(VSTOP)
|
||
// TMC5160_SPIWriteInt(0x2C, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 23 = 0x2C(TZEROWAIT)
|
||
// TMC5160_SPIWriteInt(0x2D, 0x00000000,1); // writing value 0xFFCC12F0 = 0 = 0.0 to address 24 = 0x2D(XTARGET)
|
||
|
||
// TMC5160_SPIWriteInt(0x33, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 25 = 0x33(VDCMIN)
|
||
// TMC5160_SPIWriteInt(0x34, 0x00000000,1); // writing value 0x00000400 = 1024 = 0.0 to address 26 = 0x34(SW_MODE)
|
||
// // 编码器寄存器
|
||
// TMC5160_SPIWriteInt(0x38, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 27 = 0x38(ENCMODE)
|
||
// TMC5160_SPIWriteInt(0x39, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 28 = 0x39(X_ENC)
|
||
// TMC5160_SPIWriteInt(0x3A, 0x00010000,1); // writing value 0x00010000 = 65536 = 0.0 to address 29 = 0x3A(ENC_CONST)
|
||
// TMC5160_SPIWriteInt(0x3D, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 30 = 0x3D(ENC_DEVIATION)
|
||
// // 电机驱动寄存器-电机微步控制寄存器
|
||
// TMC5160_SPIWriteInt(0x60, 0xAAAAB554,1); // writing value 0xAAAAB554 = 0 = 0.0 to address 31 = 0x60(MSLUT[0])
|
||
// TMC5160_SPIWriteInt(0x61, 0x4A9554AA,1); // writing value 0x4A9554AA = 1251300522 = 0.0 to address 32 = 0x61(MSLUT[1])
|
||
// TMC5160_SPIWriteInt(0x62, 0x24492929,1); // writing value 0x24492929 = 608774441 = 0.0 to address 33 = 0x62(MSLUT[2])
|
||
// TMC5160_SPIWriteInt(0x63, 0x10104222,1); // writing value 0x10104222 = 269500962 = 0.0 to address 34 = 0x63(MSLUT[3])
|
||
// TMC5160_SPIWriteInt(0x64, 0xFBFFFFFF,1); // writing value 0xFBFFFFFF = 0 = 0.0 to address 35 = 0x64(MSLUT[4])
|
||
// TMC5160_SPIWriteInt(0x65, 0xB5BB777D,1); // writing value 0xB5BB777D = 0 = 0.0 to address 36 = 0x65(MSLUT[5])
|
||
// TMC5160_SPIWriteInt(0x66, 0x49295556,1); // writing value 0x49295556 = 1227445590 = 0.0 to address 37 = 0x66(MSLUT[6])
|
||
// TMC5160_SPIWriteInt(0x67, 0x00404222,1); // writing value 0x00404222 = 4211234 = 0.0 to address 38 = 0x67(MSLUT[7])
|
||
// TMC5160_SPIWriteInt(0x68, 0xFFFF8056,1); // writing value 0xFFFF8056 = 0 = 0.0 to address 39 = 0x68(MSLUTSEL)
|
||
// TMC5160_SPIWriteInt(0x69, 0x00F70000,1); // writing value 0x00F70000 = 16187392 = 0.0 to address 40 = 0x69(MSLUTSTART)
|
||
// // 电机驱动寄存器-驱动寄存器组
|
||
// TMC5160_SPIWriteInt(0x6C, 0x04410153,1); // writing value 0x00410153 = 4260179 = 0.0 to address 41 = 0x6C(CHOPCONF)
|
||
// TMC5160_SPIWriteInt(0x6D, 0x00000000,1); // writing value 0x00030000 = 196608 = 0.0 to address 42 = 0x6D(COOLCONF)
|
||
// TMC5160_SPIWriteInt(0x6E, 0x00000000,1); // writing value 0x00000000 = 0 = 0.0 to address 43 = 0x6E(DCCTRL)
|
||
// TMC5160_SPIWriteInt(0x70, 0xC40C001E,1); // writing value 0xC40C001E = 0 = 0.0 to address 44 = 0x70(PWMCONF)
|
||
}
|
||
|
||
uint8_t data_r[5] = {0};//存放接收到的数据
|
||
|
||
void TMC5160_SPIWriteInt(uint8_t addr, uint32_t data, uint8_t rw)//rw = 1为写，0为读
|
||
{
|
||
|
||
char i = 0;
|
||
unsigned long dat = 0;
|
||
for(i = 0; i < 5; i++) data_r[i] = 0;
|
||
|
||
TMC5160A_CS2_L;
|
||
delay(100);
|
||
if(rw)
|
||
{
|
||
addr |= 0x80;
|
||
}
|
||
else
|
||
{
|
||
addr &= 0x7F;
|
||
}
|
||
|
||
//地址
|
||
TMC5160A_CLK_H;
|
||
for(i = 0; i < 8; i++)
|
||
{
|
||
TMC5160A_CLK_L;
|
||
if(addr & 0x80)
|
||
{
|
||
TMC5160A_MOSI_H;
|
||
}
|
||
else
|
||
{
|
||
TMC5160A_MOSI_L;
|
||
}
|
||
|
||
addr <<= 1;
|
||
TMC5160A_CLK_H;
|
||
delay(20);
|
||
|
||
data_r[0] <<= 1;
|
||
if(TMC5160A_ReadVal)
|
||
{
|
||
data_r[0] |= 1;
|
||
}
|
||
|
||
|
||
|
||
}
|
||
//数据
|
||
for(i = 0; i < 32; i++)
|
||
{
|
||
TMC5160A_CLK_L;
|
||
if(data & 0x80000000)
|
||
{
|
||
TMC5160A_MOSI_H;
|
||
}
|
||
else
|
||
{
|
||
TMC5160A_MOSI_L;
|
||
}
|
||
data <<= 1;
|
||
TMC5160A_CLK_H;
|
||
delay(20);
|
||
|
||
dat <<= 1;
|
||
if(TMC5160A_ReadVal)
|
||
{
|
||
dat |= 1;
|
||
}
|
||
|
||
}
|
||
|
||
data_r[0] = addr;
|
||
data_r[1] = dat >> 24;
|
||
data_r[2] = dat >> 16;
|
||
data_r[3] = dat >> 8;
|
||
data_r[4] = dat >> 0;
|
||
|
||
|
||
TMC5160A_CS2_H; //SPI_CS片选拉1
|
||
|
||
}
|
||
|
||
void TMC5160_SPIReadInt(uint8_t addr, uint8_t record[5])//从addr寄存器读取数据，然后记录到record中
|
||
{
|
||
char i;
|
||
for(i = 0; i < 5; i++) data_r[i] = 0;
|
||
|
||
TMC5160_SPIWriteInt(addr,0,0);
|
||
TMC5160_SPIWriteInt(addr,0,0);
|
||
memcpy(record, data_r, 5);
|
||
}
|
||
|
||
uint8_t XA[5]={0},VA[5]={0};
|
||
void tmc5160_act()
|
||
{
|
||
TMC5160_SPIReadInt(0x21,XA);//读取实际位置XACTUAL
|
||
|
||
TMC5160_SPIReadInt(0x20,VA);//读取实际速度VACTUAL
|
||
|
||
// TMC5160_SPIWriteInt(0x20,0x00000001,1);//RAMPMODE = 1 速度模式至+VMAX
|
||
// TMC5160_SPIWriteInt(0x2D,0x0000C800,1); //设置目标位置
|
||
// TMC5160_SPIWriteInt(0x2D,(uint32_t)0xADFFFF3800,1); //XTARGET = -51200 反向转动一圈
|
||
|
||
|
||
|
||
}
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|