CubeMX版本更新

Core/Inc/stm32f4xx_hal_conf.h

@@ -221,8 +221,8 @@
 
 /* Section 2: PHY configuration section */
 
-/* DP83848_PHY_ADDRESS Address*/
+/* LAN8742A PHY Address*/
-#define DP83848_PHY_ADDRESS           0x01U
+#define LAN8742A_PHY_ADDRESS           0x00U
 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
 #define PHY_RESET_DELAY                 0x000000FFU
 /* PHY Configuration delay */
@@ -252,10 +252,13 @@
 #define PHY_JABBER_DETECTION            ((uint16_t)0x0002U)  /*!< Jabber condition detected            */
 
 /* Section 4: Extended PHY Registers */
-#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
+#define PHY_SR                          ((uint16_t)0x001FU)    /*!< PHY status register Offset                      */
 
-#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
+#define PHY_SPEED_STATUS                ((uint16_t)0x0004U)  /*!< PHY Speed mask                                  */
-#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0010U)  /*!< PHY Duplex mask                                 */
+
+#define PHY_ISFR                        ((uint16_t)0x1DU)    /*!< PHY Interrupt Source Flag register Offset   */
+#define PHY_ISFR_INT4                   ((uint16_t)0x0010U)  /*!< PHY Link down inturrupt       */
 
 /* ################## SPI peripheral configuration ########################## */
 

Core/Src/dma.c

@@ -74,8 +74,10 @@ void MX_DMA_Init(void)
   /* DMA2_Stream7_IRQn interrupt configuration */
   HAL_NVIC_SetPriority(DMA2_Stream7_IRQn, 5, 0);
   HAL_NVIC_EnableIRQ(DMA2_Stream7_IRQn);
+
 }
 
 /* USER CODE BEGIN 2 */
 
 /* USER CODE END 2 */
+

Core/Src/main.c

@@ -157,6 +157,7 @@ int main(void)
 
   /* Start scheduler */
   osKernelStart();
+
   /* We should never get here as control is now taken by the scheduler */
   /* Infinite loop */
   /* USER CODE BEGIN WHILE */
@@ -201,7 +202,8 @@ void SystemClock_Config(void)
 
   /** Initializes the CPU, AHB and APB buses clocks
   */
-  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
   RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
   RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
   RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
@@ -366,8 +368,7 @@ void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim)
   /* USER CODE BEGIN Callback 0 */
 
   /* USER CODE END Callback 0 */
-  if (htim->Instance == TIM4)
+  if (htim->Instance == TIM4) {
-  {
     HAL_IncTick();
   }
   /* USER CODE BEGIN Callback 1 */

Core/Src/stm32f4xx_hal_msp.c

@@ -20,6 +20,7 @@
 
 /* Includes ------------------------------------------------------------------*/
 #include "main.h"
+
 /* USER CODE BEGIN Includes */
 
 /* USER CODE END Includes */

Core/Src/usart.c

@@ -66,6 +66,7 @@ void MX_UART4_Init(void)
   /* USER CODE BEGIN UART4_Init 2 */
   //__HAL_UART_ENABLE_IT(&huart4, UART_IT_IDLE); // 使能IDLE中断
   /* USER CODE END UART4_Init 2 */
+
 }
 /* UART5 init function */
 void MX_UART5_Init(void)
@@ -94,6 +95,7 @@ void MX_UART5_Init(void)
   // __HAL_UART_ENABLE_IT(&huart5, UART_IT_RXNE); // 接收中断
   // __HAL_UART_ENABLE_IT(&huart5, UART_IT_IDLE); // 空闲中断
   /* USER CODE END UART5_Init 2 */
+
 }
 /* USART1 init function */
 
@@ -122,6 +124,7 @@ void MX_USART1_UART_Init(void)
   /* USER CODE BEGIN USART1_Init 2 */
 
   /* USER CODE END USART1_Init 2 */
+
 }
 /* USART2 init function */
 
@@ -151,6 +154,7 @@ void MX_USART2_UART_Init(void)
   // __HAL_UART_ENABLE_IT(&huart2, UART_IT_RXNE); // 接收中断
   // __HAL_UART_ENABLE_IT(&huart2, UART_IT_IDLE); // 使能IDLE中断
   /* USER CODE END USART2_Init 2 */
+
 }
 /* USART3 init function */
 
@@ -179,13 +183,14 @@ void MX_USART3_UART_Init(void)
   /* USER CODE BEGIN USART3_Init 2 */
 
   /* USER CODE END USART3_Init 2 */
+
 }
 
-void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
+void HAL_UART_MspInit(UART_HandleTypeDef* uartHandle)
 {
 
   GPIO_InitTypeDef GPIO_InitStruct = {0};
-  if (uartHandle->Instance == UART4)
+  if(uartHandle->Instance==UART4)
   {
   /* USER CODE BEGIN UART4_MspInit 0 */
 
@@ -198,7 +203,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
     PC10     ------> UART4_TX
     PC11     ------> UART4_RX
     */
-    GPIO_InitStruct.Pin = LCD_TX_Pin | LCD_RX_Pin;
+    GPIO_InitStruct.Pin = LCD_TX_Pin|LCD_RX_Pin;
     GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
     GPIO_InitStruct.Pull = GPIO_NOPULL;
     GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
@@ -222,7 +227,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmarx, hdma_uart4_rx);
+    __HAL_LINKDMA(uartHandle,hdmarx,hdma_uart4_rx);
 
     /* UART4_TX Init */
     hdma_uart4_tx.Instance = DMA1_Stream4;
@@ -240,7 +245,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmatx, hdma_uart4_tx);
+    __HAL_LINKDMA(uartHandle,hdmatx,hdma_uart4_tx);
 
     /* UART4 interrupt Init */
     HAL_NVIC_SetPriority(UART4_IRQn, 5, 0);
@@ -249,7 +254,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END UART4_MspInit 1 */
   }
-  else if (uartHandle->Instance == UART5)
+  else if(uartHandle->Instance==UART5)
   {
   /* USER CODE BEGIN UART5_MspInit 0 */
 
@@ -294,7 +299,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmatx, hdma_uart5_tx);
+    __HAL_LINKDMA(uartHandle,hdmatx,hdma_uart5_tx);
 
     /* UART5_RX Init */
     hdma_uart5_rx.Instance = DMA1_Stream0;
@@ -312,7 +317,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmarx, hdma_uart5_rx);
+    __HAL_LINKDMA(uartHandle,hdmarx,hdma_uart5_rx);
 
     /* UART5 interrupt Init */
     HAL_NVIC_SetPriority(UART5_IRQn, 5, 0);
@@ -321,7 +326,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END UART5_MspInit 1 */
   }
-  else if (uartHandle->Instance == USART1)
+  else if(uartHandle->Instance==USART1)
   {
   /* USER CODE BEGIN USART1_MspInit 0 */
 
@@ -334,7 +339,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
     PA9     ------> USART1_TX
     PA10     ------> USART1_RX
     */
-    GPIO_InitStruct.Pin = USB_TX_Pin | USB_RX_Pin;
+    GPIO_InitStruct.Pin = USB_TX_Pin|USB_RX_Pin;
     GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
     GPIO_InitStruct.Pull = GPIO_NOPULL;
     GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
@@ -358,7 +363,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmarx, hdma_usart1_rx);
+    __HAL_LINKDMA(uartHandle,hdmarx,hdma_usart1_rx);
 
     /* USART1_TX Init */
     hdma_usart1_tx.Instance = DMA2_Stream7;
@@ -376,7 +381,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmatx, hdma_usart1_tx);
+    __HAL_LINKDMA(uartHandle,hdmatx,hdma_usart1_tx);
 
     /* USART1 interrupt Init */
     HAL_NVIC_SetPriority(USART1_IRQn, 5, 0);
@@ -385,7 +390,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END USART1_MspInit 1 */
   }
-  else if (uartHandle->Instance == USART2)
+  else if(uartHandle->Instance==USART2)
   {
   /* USER CODE BEGIN USART2_MspInit 0 */
 
@@ -398,7 +403,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
     PD5     ------> USART2_TX
     PD6     ------> USART2_RX
     */
-    GPIO_InitStruct.Pin = HART2_TX_Pin | HART2_RX_Pin;
+    GPIO_InitStruct.Pin = HART2_TX_Pin|HART2_RX_Pin;
     GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
     GPIO_InitStruct.Pull = GPIO_NOPULL;
     GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
@@ -422,7 +427,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmarx, hdma_usart2_rx);
+    __HAL_LINKDMA(uartHandle,hdmarx,hdma_usart2_rx);
 
     /* USART2_TX Init */
     hdma_usart2_tx.Instance = DMA1_Stream6;
@@ -440,7 +445,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmatx, hdma_usart2_tx);
+    __HAL_LINKDMA(uartHandle,hdmatx,hdma_usart2_tx);
 
     /* USART2 interrupt Init */
     HAL_NVIC_SetPriority(USART2_IRQn, 5, 0);
@@ -449,7 +454,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END USART2_MspInit 1 */
   }
-  else if (uartHandle->Instance == USART3)
+  else if(uartHandle->Instance==USART3)
   {
   /* USER CODE BEGIN USART3_MspInit 0 */
 
@@ -462,7 +467,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
     PD8     ------> USART3_TX
     PD9     ------> USART3_RX
     */
-    GPIO_InitStruct.Pin = BLE2_TX_Pin | BLE2_RX_Pin;
+    GPIO_InitStruct.Pin = BLE2_TX_Pin|BLE2_RX_Pin;
     GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
     GPIO_InitStruct.Pull = GPIO_PULLUP;
     GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
@@ -486,7 +491,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmarx, hdma_usart3_rx);
+    __HAL_LINKDMA(uartHandle,hdmarx,hdma_usart3_rx);
 
     /* USART3_TX Init */
     hdma_usart3_tx.Instance = DMA1_Stream3;
@@ -504,7 +509,7 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
       Error_Handler();
     }
 
-    __HAL_LINKDMA(uartHandle, hdmatx, hdma_usart3_tx);
+    __HAL_LINKDMA(uartHandle,hdmatx,hdma_usart3_tx);
 
     /* USART3 interrupt Init */
     HAL_NVIC_SetPriority(USART3_IRQn, 5, 0);
@@ -515,10 +520,10 @@ void HAL_UART_MspInit(UART_HandleTypeDef *uartHandle)
   }
 }
 
-void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
+void HAL_UART_MspDeInit(UART_HandleTypeDef* uartHandle)
 {
 
-  if (uartHandle->Instance == UART4)
+  if(uartHandle->Instance==UART4)
   {
   /* USER CODE BEGIN UART4_MspDeInit 0 */
 
@@ -530,7 +535,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
     PC10     ------> UART4_TX
     PC11     ------> UART4_RX
     */
-    HAL_GPIO_DeInit(GPIOC, LCD_TX_Pin | LCD_RX_Pin);
+    HAL_GPIO_DeInit(GPIOC, LCD_TX_Pin|LCD_RX_Pin);
 
     /* UART4 DMA DeInit */
     HAL_DMA_DeInit(uartHandle->hdmarx);
@@ -542,7 +547,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END UART4_MspDeInit 1 */
   }
-  else if (uartHandle->Instance == UART5)
+  else if(uartHandle->Instance==UART5)
   {
   /* USER CODE BEGIN UART5_MspDeInit 0 */
 
@@ -568,7 +573,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END UART5_MspDeInit 1 */
   }
-  else if (uartHandle->Instance == USART1)
+  else if(uartHandle->Instance==USART1)
   {
   /* USER CODE BEGIN USART1_MspDeInit 0 */
 
@@ -580,7 +585,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
     PA9     ------> USART1_TX
     PA10     ------> USART1_RX
     */
-    HAL_GPIO_DeInit(GPIOA, USB_TX_Pin | USB_RX_Pin);
+    HAL_GPIO_DeInit(GPIOA, USB_TX_Pin|USB_RX_Pin);
 
     /* USART1 DMA DeInit */
     HAL_DMA_DeInit(uartHandle->hdmarx);
@@ -592,7 +597,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END USART1_MspDeInit 1 */
   }
-  else if (uartHandle->Instance == USART2)
+  else if(uartHandle->Instance==USART2)
   {
   /* USER CODE BEGIN USART2_MspDeInit 0 */
 
@@ -604,7 +609,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
     PD5     ------> USART2_TX
     PD6     ------> USART2_RX
     */
-    HAL_GPIO_DeInit(GPIOD, HART2_TX_Pin | HART2_RX_Pin);
+    HAL_GPIO_DeInit(GPIOD, HART2_TX_Pin|HART2_RX_Pin);
 
     /* USART2 DMA DeInit */
     HAL_DMA_DeInit(uartHandle->hdmarx);
@@ -616,7 +621,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
 
   /* USER CODE END USART2_MspDeInit 1 */
   }
-  else if (uartHandle->Instance == USART3)
+  else if(uartHandle->Instance==USART3)
   {
   /* USER CODE BEGIN USART3_MspDeInit 0 */
 
@@ -628,7 +633,7 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *uartHandle)
     PD8     ------> USART3_TX
     PD9     ------> USART3_RX
     */
-    HAL_GPIO_DeInit(GPIOD, BLE2_TX_Pin | BLE2_RX_Pin);
+    HAL_GPIO_DeInit(GPIOD, BLE2_TX_Pin|BLE2_RX_Pin);
 
     /* USART3 DMA DeInit */
     HAL_DMA_DeInit(uartHandle->hdmarx);

MDK-ARM/semi-finished_product_testing.uvoptx

@@ -1,4 +1,4 @@
-<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
+<?xml version="1.0" encoding="UTF-8"?>
 <ProjectOpt xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="project_optx.xsd">
 
   <SchemaVersion>1.0</SchemaVersion>
@@ -45,7 +45,7 @@
         <PageWidth>79</PageWidth>
         <PageLength>66</PageLength>
         <TabStop>8</TabStop>
-        <ListingPath></ListingPath>
+        <ListingPath />
       </OPTLEX>
       <ListingPage>
         <CreateCListing>1</CreateCListing>
@@ -104,16 +104,16 @@
         <bSchkAxf>0</bSchkAxf>
         <bTchkAxf>0</bTchkAxf>
         <nTsel>6</nTsel>
-        <sDll></sDll>
+        <sDll />
-        <sDllPa></sDllPa>
+        <sDllPa />
-        <sDlgDll></sDlgDll>
+        <sDlgDll />
-        <sDlgPa></sDlgPa>
+        <sDlgPa />
-        <sIfile></sIfile>
+        <sIfile />
-        <tDll></tDll>
+        <tDll />
-        <tDllPa></tDllPa>
+        <tDllPa />
-        <tDlgDll></tDlgDll>
+        <tDlgDll />
-        <tDlgPa></tDlgPa>
+        <tDlgPa />
-        <tIfile></tIfile>
+        <tIfile />
         <pMon>STLink\ST-LINKIII-KEIL_SWO.dll</pMon>
       </DebugOpt>
       <TargetDriverDllRegistry>
@@ -130,7 +130,7 @@
         <SetRegEntry>
           <Number>0</Number>
           <Key>ARMDBGFLAGS</Key>
-          <Name></Name>
+          <Name />
         </SetRegEntry>
         <SetRegEntry>
           <Number>0</Number>
@@ -154,48 +154,48 @@
           <Type>0</Type>
           <LineNumber>2413</LineNumber>
           <EnabledFlag>1</EnabledFlag>
-          <Address>134234492</Address>
+          <Address>0</Address>
           <ByteObject>0</ByteObject>
           <HtxType>0</HtxType>
           <ManyObjects>0</ManyObjects>
           <SizeOfObject>0</SizeOfObject>
           <BreakByAccess>0</BreakByAccess>
-          <BreakIfRCount>1</BreakIfRCount>
+          <BreakIfRCount>0</BreakIfRCount>
           <Filename>../Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c</Filename>
-          <ExecCommand></ExecCommand>
+          <ExecCommand />
-          <Expression>\\semi_finished_product_testing\../Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c\2413</Expression>
+          <Expression />
         </Bp>
         <Bp>
           <Number>1</Number>
           <Type>0</Type>
           <LineNumber>224</LineNumber>
           <EnabledFlag>1</EnabledFlag>
-          <Address>134234260</Address>
+          <Address>0</Address>
           <ByteObject>0</ByteObject>
           <HtxType>0</HtxType>
           <ManyObjects>0</ManyObjects>
           <SizeOfObject>0</SizeOfObject>
           <BreakByAccess>0</BreakByAccess>
-          <BreakIfRCount>1</BreakIfRCount>
+          <BreakIfRCount>0</BreakIfRCount>
           <Filename>../Core/Src/main.c</Filename>
-          <ExecCommand></ExecCommand>
+          <ExecCommand />
-          <Expression>\\semi_finished_product_testing\../Core/Src/main.c\224</Expression>
+          <Expression />
         </Bp>
         <Bp>
           <Number>2</Number>
           <Type>0</Type>
           <LineNumber>226</LineNumber>
           <EnabledFlag>1</EnabledFlag>
-          <Address>134234266</Address>
+          <Address>0</Address>
           <ByteObject>0</ByteObject>
           <HtxType>0</HtxType>
           <ManyObjects>0</ManyObjects>
           <SizeOfObject>0</SizeOfObject>
           <BreakByAccess>0</BreakByAccess>
-          <BreakIfRCount>1</BreakIfRCount>
+          <BreakIfRCount>0</BreakIfRCount>
           <Filename>../Core/Src/main.c</Filename>
-          <ExecCommand></ExecCommand>
+          <ExecCommand />
-          <Expression>\\semi_finished_product_testing\../Core/Src/main.c\226</Expression>
+          <Expression />
         </Bp>
       </Breakpoint>
       <WatchWindow1>
@@ -297,19 +297,19 @@
         <newCpu>0</newCpu>
         <uProt>0</uProt>
       </DebugFlag>
-      <LintExecutable></LintExecutable>
+      <LintExecutable />
-      <LintConfigFile></LintConfigFile>
+      <LintConfigFile />
       <bLintAuto>0</bLintAuto>
       <bAutoGenD>0</bAutoGenD>
       <LntExFlags>0</LntExFlags>
-      <pMisraName></pMisraName>
+      <pMisraName />
-      <pszMrule></pszMrule>
+      <pszMrule />
-      <pSingCmds></pSingCmds>
+      <pSingCmds />
-      <pMultCmds></pMultCmds>
+      <pMultCmds />
-      <pMisraNamep></pMisraNamep>
+      <pMisraNamep />
-      <pszMrulep></pszMrulep>
+      <pszMrulep />
-      <pSingCmdsp></pSingCmdsp>
+      <pSingCmdsp />
-      <pMultCmdsp></pMultCmdsp>
+      <pMultCmdsp />
       <DebugDescription>
         <Enable>0</Enable>
         <EnableFlashSeq>0</EnableFlashSeq>

MDK-ARM/semi-finished_product_testing.uvprojx

@@ -1,10 +1,7 @@
-<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
+<?xml version="1.0" encoding="UTF-8"?>
-<Project xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="project_projx.xsd">
+<Project xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" noNamespaceSchemaLocation="project_projx.xsd">
-
   <SchemaVersion>2.1</SchemaVersion>
-
   <Header>### uVision Project, (C) Keil Software</Header>
-
   <Targets>
     <Target>
       <TargetName>semi-finished_product_testing</TargetName>
@@ -19,28 +16,28 @@
           <PackID>Keil.STM32F4xx_DFP.2.17.1</PackID>
           <PackURL>https://www.keil.com/pack/</PackURL>
           <Cpu>IRAM(0x20000000-0x2001BFFF) IRAM2(0x2001C000-0x2001FFFF) IROM(0x8000000-0x80FFFFF) CLOCK(25000000) FPU2 CPUTYPE("Cortex-M4") TZ</Cpu>
-          <FlashUtilSpec></FlashUtilSpec>
+          <FlashUtilSpec />
-          <StartupFile></StartupFile>
+          <StartupFile />
-          <FlashDriverDll></FlashDriverDll>
+          <FlashDriverDll />
           <DeviceId>0</DeviceId>
-          <RegisterFile></RegisterFile>
+          <RegisterFile />
-          <MemoryEnv></MemoryEnv>
+          <MemoryEnv />
-          <Cmp></Cmp>
+          <Cmp />
-          <Asm></Asm>
+          <Asm />
-          <Linker></Linker>
+          <Linker />
-          <OHString></OHString>
+          <OHString />
-          <InfinionOptionDll></InfinionOptionDll>
+          <InfinionOptionDll />
-          <SLE66CMisc></SLE66CMisc>
+          <SLE66CMisc />
-          <SLE66AMisc></SLE66AMisc>
+          <SLE66AMisc />
-          <SLE66LinkerMisc></SLE66LinkerMisc>
+          <SLE66LinkerMisc />
           <SFDFile>$$Device:STM32F407VGTx$CMSIS\SVD\STM32F40x.svd</SFDFile>
           <bCustSvd>0</bCustSvd>
           <UseEnv>0</UseEnv>
-          <BinPath></BinPath>
+          <BinPath />
-          <IncludePath></IncludePath>
+          <IncludePath />
-          <LibPath></LibPath>
+          <LibPath />
-          <RegisterFilePath></RegisterFilePath>
+          <RegisterFilePath />
-          <DBRegisterFilePath></DBRegisterFilePath>
+          <DBRegisterFilePath />
           <TargetStatus>
             <Error>0</Error>
             <ExitCodeStop>0</ExitCodeStop>
@@ -55,15 +52,15 @@
           <CreateHexFile>1</CreateHexFile>
           <DebugInformation>1</DebugInformation>
           <BrowseInformation>0</BrowseInformation>
-          <ListingPath></ListingPath>
+          <ListingPath />
           <HexFormatSelection>1</HexFormatSelection>
           <Merge32K>0</Merge32K>
           <CreateBatchFile>0</CreateBatchFile>
           <BeforeCompile>
             <RunUserProg1>0</RunUserProg1>
             <RunUserProg2>0</RunUserProg2>
-            <UserProg1Name></UserProg1Name>
+            <UserProg1Name />
-            <UserProg2Name></UserProg2Name>
+            <UserProg2Name />
             <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
             <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
             <nStopU1X>0</nStopU1X>
@@ -72,8 +69,8 @@
           <BeforeMake>
             <RunUserProg1>0</RunUserProg1>
             <RunUserProg2>0</RunUserProg2>
-            <UserProg1Name></UserProg1Name>
+            <UserProg1Name />
-            <UserProg2Name></UserProg2Name>
+            <UserProg2Name />
             <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
             <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
             <nStopB1X>0</nStopB1X>
@@ -82,15 +79,15 @@
           <AfterMake>
             <RunUserProg1>0</RunUserProg1>
             <RunUserProg2>0</RunUserProg2>
-            <UserProg1Name></UserProg1Name>
+            <UserProg1Name />
-            <UserProg2Name></UserProg2Name>
+            <UserProg2Name />
             <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
             <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
             <nStopA1X>0</nStopA1X>
             <nStopA2X>0</nStopA2X>
           </AfterMake>
           <SelectedForBatchBuild>1</SelectedForBatchBuild>
-          <SVCSIdString></SVCSIdString>
+          <SVCSIdString />
         </TargetCommonOption>
         <CommonProperty>
           <UseCPPCompiler>0</UseCPPCompiler>
@@ -104,8 +101,8 @@
           <AssembleAssemblyFile>0</AssembleAssemblyFile>
           <PublicsOnly>0</PublicsOnly>
           <StopOnExitCode>3</StopOnExitCode>
-          <CustomArgument></CustomArgument>
+          <CustomArgument />
-          <IncludeLibraryModules></IncludeLibraryModules>
+          <IncludeLibraryModules />
           <ComprImg>0</ComprImg>
         </CommonProperty>
         <DllOption>
@@ -139,10 +136,10 @@
           <bUseTDR>1</bUseTDR>
           <Flash2>BIN\UL2V8M.DLL</Flash2>
           <Flash3>"" ()</Flash3>
-          <Flash4></Flash4>
+          <Flash4 />
-          <pFcarmOut></pFcarmOut>
+          <pFcarmOut />
-          <pFcarmGrp></pFcarmGrp>
+          <pFcarmGrp />
-          <pFcArmRoot></pFcArmRoot>
+          <pFcArmRoot />
           <FcArmLst>0</FcArmLst>
         </Utilities>
         <TargetArmAds>
@@ -175,7 +172,7 @@
             <RvctClst>0</RvctClst>
             <GenPPlst>0</GenPPlst>
             <AdsCpuType>"Cortex-M4"</AdsCpuType>
-            <RvctDeviceName></RvctDeviceName>
+            <RvctDeviceName />
             <mOS>0</mOS>
             <uocRom>0</uocRom>
             <uocRam>0</uocRam>
@@ -309,7 +306,7 @@
                 <Size>0x4000</Size>
               </OCR_RVCT10>
             </OnChipMemories>
-            <RvctStartVector></RvctStartVector>
+            <RvctStartVector />
           </ArmAdsMisc>
           <Cads>
             <interw>1</interw>
@@ -336,9 +333,9 @@
             <v6WtE>0</v6WtE>
             <v6Rtti>0</v6Rtti>
             <VariousControls>
-              <MiscControls></MiscControls>
+              <MiscControls />
               <Define>USE_HAL_DRIVER,STM32F407xx</Define>
-              <Undefine></Undefine>
+              <Undefine />
               <IncludePath>../Core/Inc;../LWIP/App;../LWIP/Target;../Middlewares/Third_Party/LwIP/src/include;../Middlewares/Third_Party/LwIP/system;../Drivers/STM32F4xx_HAL_Driver/Inc;../Drivers/STM32F4xx_HAL_Driver/Inc/Legacy;../Middlewares/Third_Party/FreeRTOS/Source/include;../Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS;../Middlewares/Third_Party/FreeRTOS/Source/portable/RVDS/ARM_CM4F;../Drivers/BSP/Components/lan8742;../Middlewares/Third_Party/LwIP/src/include/netif/ppp;../Drivers/CMSIS/Device/ST/STM32F4xx/Include;../Middlewares/Third_Party/LwIP/src/include/lwip;../Middlewares/Third_Party/LwIP/src/include/lwip/apps;../Middlewares/Third_Party/LwIP/src/include/lwip/priv;../Middlewares/Third_Party/LwIP/src/include/lwip/prot;../Middlewares/Third_Party/LwIP/src/include/netif;../Middlewares/Third_Party/LwIP/src/include/compat/posix;../Middlewares/Third_Party/LwIP/src/include/compat/posix/arpa;../Middlewares/Third_Party/LwIP/src/include/compat/posix/net;../Middlewares/Third_Party/LwIP/src/include/compat/posix/sys;../Middlewares/Third_Party/LwIP/src/include/compat/stdc;../Middlewares/Third_Party/LwIP/system/arch;../Drivers/CMSIS/Include;../User/application/inc;../User/board/inc;../User/driver;../User/system</IncludePath>
             </VariousControls>
           </Cads>
@@ -354,9 +351,9 @@
             <useXO>0</useXO>
             <ClangAsOpt>1</ClangAsOpt>
             <VariousControls>
-              <MiscControls></MiscControls>
+              <MiscControls />
-              <Define></Define>
+              <Define />
-              <Undefine></Undefine>
+              <Undefine />
               <IncludePath>../Core/Inc</IncludePath>
             </VariousControls>
           </Aads>
@@ -367,15 +364,15 @@
             <noStLib>0</noStLib>
             <RepFail>1</RepFail>
             <useFile>0</useFile>
-            <TextAddressRange></TextAddressRange>
+            <TextAddressRange />
-            <DataAddressRange></DataAddressRange>
+            <DataAddressRange />
-            <pXoBase></pXoBase>
+            <pXoBase />
-            <ScatterFile></ScatterFile>
+            <ScatterFile />
-            <IncludeLibs></IncludeLibs>
+            <IncludeLibs />
-            <IncludeLibsPath></IncludeLibsPath>
+            <IncludeLibsPath />
-            <Misc></Misc>
+            <Misc />
-            <LinkerInputFile></LinkerInputFile>
+            <LinkerInputFile />
-            <DisabledWarnings></DisabledWarnings>
+            <DisabledWarnings />
           </LDads>
         </TargetArmAds>
       </TargetOption>
@@ -1141,20 +1138,18 @@
       </Groups>
     </Target>
   </Targets>
-
   <RTE>
-    <apis/>
+    <apis />
     <components>
       <component Cclass="CMSIS" Cgroup="CORE" Cvendor="ARM" Cversion="4.3.0" condition="CMSIS Core">
-        <package name="CMSIS" schemaVersion="1.3" url="http://www.keil.com/pack/" vendor="ARM" version="4.5.0"/>
+        <package name="CMSIS" schemaVersion="1.3" url="http://www.keil.com/pack/" vendor="ARM" version="4.5.0" />
         <targetInfos>
-          <targetInfo name="semi-finished_product_testing"/>
+          <targetInfo name="semi-finished_product_testing" />
         </targetInfos>
       </component>
     </components>
-    <files/>
+    <files />
   </RTE>
-
   <LayerInfo>
     <Layers>
       <Layer>
@@ -1163,5 +1158,5 @@
       </Layer>
     </Layers>
   </LayerInfo>
-
 </Project>
+

semi-finished_product_testing.ioc

@@ -238,8 +238,8 @@ Mcu.PinsNb=67
 Mcu.ThirdPartyNb=0
 Mcu.UserConstants=
 Mcu.UserName=STM32F407VGTx
-MxCube.Version=6.8.0
+MxCube.Version=6.9.2
-MxDb.Version=DB.6.0.80
+MxDb.Version=DB.6.0.92
 NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false\:false
 NVIC.DMA1_Stream0_IRQn=true\:5\:0\:true\:false\:true\:true\:false\:true\:true
 NVIC.DMA1_Stream1_IRQn=true\:5\:0\:false\:false\:true\:true\:false\:true\:true
@@ -606,6 +606,8 @@ ProjectManager.RegisterCallBack=
 ProjectManager.StackSize=0x400
 ProjectManager.TargetToolchain=MDK-ARM V5.32
 ProjectManager.ToolChainLocation=
+ProjectManager.UAScriptAfterPath=
+ProjectManager.UAScriptBeforePath=
 ProjectManager.UnderRoot=false
 ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_DMA_Init-DMA-false-HAL-true,4-MX_LWIP_Init-LWIP-false-HAL-false,5-MX_TIM3_Init-TIM3-false-HAL-true,6-MX_SPI1_Init-SPI1-false-HAL-true,7-MX_UART4_Init-UART4-false-HAL-true,8-MX_TIM2_Init-TIM2-false-HAL-true,9-MX_UART5_Init-UART5-false-HAL-true,10-MX_USART2_UART_Init-USART2-false-HAL-true,11-MX_USART3_UART_Init-USART3-false-HAL-true,12-MX_TIM1_Init-TIM1-false-HAL-true,13-MX_USART1_UART_Init-USART1-false-HAL-true,14-MX_TIM8_Init-TIM8-false-HAL-true
 RCC.48MHZClocksFreq_Value=55296000